How to use optical fiber recoater

Categories

New Products

LDC-100 Large Diameter Optical Fiber Cleaver * Applicable to cladding diameter 80μm~1250μm fibers * Vacuum pump V-groove convenient to put fiber * Durable blade, lifetime more than 20000 times * Data storage 4000 groups * User friendly GUI menu, easy to operate more
S-22 Multi-Core Fiber Fusion Splicer The 1st Fully Automatic Multi-core Fiber Fusion Splicer in China more
Polarization Maintaining (PM) Fiber Fusion Splicer S-12 *Suitable for SM/MM/PM fibers splicing * Core to core alignment, low splicing loss * Endview and Profile observation and alignment * Arc automatic calibration and splicing * PM fiber 45 and 90 degree alignment * Applicable to variety fibers splicing, such as Panda ,bow-tie and elliptical fiber more
S-37 LDF Speialty Fiber Fusion Splicer SHINHO S-37 is the latest model we developed, it could splice fiber cladding diameter from 125 to 500μm with low splice loss. We equipped the machine with 3 different fiber holders, and 2 pairs of spare electrodes. more
Core to Core Alignment Fiber Fusion Splicer X900 Six motors fusion splicer, real core to core alignment technology. Typical splicing time: 6-12 seconds, fast splicing 6 seconds Typical heating time: 18s heating, identify fiber types automatically. Typical splice loss:G651: 0.01dB; G652: 0.02dB; G653: 0.04dB; G654: 0.04dB; G.655:0.04dB; G657:0.02dB. Battery Capacity: 5200mAh Li-battery, typical 300 cycles splicing and heating. Used for WAN/ MAN/ Telecommunication projects. more
Robust Multi Function ARC Fusion Splicer S16 76cm dropping anti-shock, IP5X dustproof and IPX2 water resistant Touch screen display, combined with keypad operation Multi function holder for bare fiber, patch cords, drop cable etc. Fast splicing and heating, automatic ARC calibration. more
SHINHO X-18 Ribbon Fiber Thermal Stripper Shinho X-18 Thermal Stripper is a newly developed hand-held thermal stripper, specially designed for nondestructive thermal stripping of the jacket of ribbon cable up to 12 fibers. A good and reliable tool for ribbon fiber splicing work. more
High Precision Fiber Optic Cleaver X-50D Small size& light weight, easy to operate. High precision and stable performance. More than 48000 time blade life,fiber cleaved length 5~20mm. High quality material more

How to use optical fiber recoater

2024-05-31

How to use the optical fiber recoater?

First, place the optical fiber to be coated in the position shown in the figure below, and align the center of the coated optical fiber with the injection port so that the machine can coat evenly on the left and right.

Before the coating operation, you need to inject a small amount of UV curing material into the glass mold of the optical fiber recoater, and confirm that there are no bubbles in the UV curing material. Open the mold cover, press the Purge key, and run the pump. Inject the UV curing material from the bottle into the glass mold. After the injection amount is as shown in the figure, press the Purge key again to stop the injection.

Close the mold cover, open the upper lamp cover, and press the Start key to inject the resin. From the window shown in the figure, you can observe the UV curing material reaching the target point of the optical fiber. Press the Purge key to pause the coating if the UV curing material has reached the target point and the machine has not stopped. If the UV curing material has not reached the target point, press the Add key to increase the injection amount. After reaching the target point, press the Add key again to stop the injection.

Note: 1. When injecting UV curing glue, be sure to open the upper lamp cover. Since the injection time is controlled by the parameter setting time, it is impossible to completely and accurately cover the target optical fiber. 2. If the entire glass mold is opened after the UV curing material is injected, the material will leak out of the groove, so it needs to be re-coated.

When the coating operation is completed, close the upper lamp cover and press the Start button to turn on the UV curing lamp. The optical fiber can be removed only after the buzzer prompts.

Note: When the UV lamp is working, be sure not to open the glass mold and the upper lamp cover. Otherwise, it will affect the curing effect.

After the optical fiber is taken out, immediately wipe the upper and lower glass molds of the optical fiber recoater with dust-free cotton or dust-free cloth containing alcohol. If the UV curing material remaining on the glass mold is not removed, the curing material will stick to the upper and lower glass molds and damage the surface finish of the glass mold. When re-coating, irregular coating will be formed. The specific cleaning operation is shown in the figure below.

Note: Place a dust-free cloth or soft tissue between the upper and lower glass molds when storing or not using the machine.

The FR-100 optical fiber recoater independently developed and produced by Xianghe Communication has a variety of coating programs to choose from, automatic cleaning function, and convenient resin replacement and addition.