Why Your Fusion Splicer is Mission Critical in Fiber Laser Repairing Work

Categories

New Products

LDC-100 Large Diameter Optical Fiber Cleaver * Applicable to cladding diameter 80μm~1250μm fibers * Vacuum pump V-groove convenient to put fiber * Durable blade, lifetime more than 20000 times * Data storage 4000 groups * User friendly GUI menu, easy to operate more
S-22 Multi-Core Fiber Fusion Splicer The 1st Fully Automatic Multi-core Fiber Fusion Splicer in China more
Polarization Maintaining (PM) Fiber Fusion Splicer S-12 *Suitable for SM/MM/PM fibers splicing * Core to core alignment, low splicing loss * Endview and Profile observation and alignment * Arc automatic calibration and splicing * PM fiber 45 and 90 degree alignment * Applicable to variety fibers splicing, such as Panda ,bow-tie and elliptical fiber more
S-37 LDF Speialty Fiber Fusion Splicer SHINHO S-37 is the latest model we developed, it could splice fiber cladding diameter from 125 to 680μm with low splice loss. We equipped the machine with 3 different fiber holders, and 2 pairs of spare electrodes. more
Core to Core Alignment Fiber Fusion Splicer X900 Six motors fusion splicer, real core to core alignment technology. Typical splicing time: 6-12 seconds, fast splicing 6 seconds Typical heating time: 18s heating, identify fiber types automatically. Typical splice loss:G651: 0.01dB; G652: 0.02dB; G653: 0.04dB; G654: 0.04dB; G.655:0.04dB; G657:0.02dB. Battery Capacity: 5200mAh Li-battery, typical 300 cycles splicing and heating. Used for WAN/ MAN/ Telecommunication projects. more
Robust Multi Function ARC Fusion Splicer S16 76cm dropping anti-shock, IP5X dustproof and IPX2 water resistant Touch screen display, combined with keypad operation Multi function holder for bare fiber, patch cords, drop cable etc. Fast splicing and heating, automatic ARC calibration. more
SHINHO X-18 Ribbon Fiber Thermal Stripper Shinho X-18 Thermal Stripper is a newly developed hand-held thermal stripper, specially designed for nondestructive thermal stripping of the jacket of ribbon cable up to 12 fibers. A good and reliable tool for ribbon fiber splicing work. more
High Precision Fiber Optic Cleaver X-50D Small size& light weight, easy to operate. High precision and stable performance. More than 48000 time blade life,fiber cleaved length 5~20mm. High quality material more

Why Your Fusion Splicer is Mission Critical in Fiber Laser Repairing Work

2025-06-27

1.What Does This "Fiber Splicer" Actually Fix?

Broken Wires (Fibers): Inside the laser, super-thin glass fibers carry the light. These can snap during handling, get bent too far, or get damaged by heat or dirt. You can't just plug them back together like an extension cord deep inside. The splicer cuts out the bad piece and permanently welds in a new section of matching fiber, making the light path whole again with almost no loss.

Replacing Worn-Out Parts: Lasers have special protective tips (like end caps) on their output fibers. If these get damaged or stop working well, the whole laser suffers. The splicer carefully welds the laser's internal fiber onto a brand-new replacement tip, which is a very precise job.

Adding New Bits: Sometimes a repair means putting in a new part, like an isolator (which stops harmful light reflections). These parts have their own little fiber tails. The splicer welds these tails directly onto the laser's existing fibers, making a strong, low-loss connection inside the machine.

2.Why is Welding Fibers Better Than Other Ways?

Almost No Power Loss: Every bit of light matters in a laser. A good fiber weld loses way less light power than any connector you could screw on.

Stops Harmful Reflections: Reflected light bouncing back inside a laser is bad news – it can make the laser unstable or even damage it. A clean fiber weld creates much less reflection than connectors.

Super Strong & Reliable: Once welded and protected with a sleeve, the joint becomes incredibly strong. It handles vibration and heat changes inside the laser much better than connectors that could come loose or get dirty over time. It's a permanent fix.

Fewer Weak Spots: Welding means fewer connection points inside the laser where things could potentially go wrong later.

3.The Bottom Line for Fixing Lasers:

If you work on fiber lasers, a good fusion splicer isn't just a nice-to-have tool; it's absolutely necessary. You simply can't do reliable, high-quality repairs on these machines without one.

It delivers the strong, low-loss, low-reflection connections that keep the laser running powerfully, efficiently, and reliably after the repair.

Investing in a quality fusion splicer and learning how to use it well is fundamental for any team serious about fixing fiber lasers quickly and getting them working like new again. When the laser stops, this "fiber splicer" is your best choice.

Next :
Fusion splicing operation